Email: info@falgateaggregates.co.ukEmail usPhone: 07450 701529Call usMonday – Friday 08:00–17:00Order before 1pm for next-day delivery

Type 1, 6F2 or recycled? Choosing a sub-base

The difference between Type 1 limestone, recycled Type 1, steel slag, IBAA, 6F2 and 6F5, and when to use clean stone or 20/40mm crush instead.

What a sub-base does

A sub-base is the compacted layer under paving, tarmac, concrete or gravel. It spreads the load, resists movement and gives the surface a firm, level base. The right material depends on what will sit on top, the ground conditions and any specification for the job.

Type 1 (MOT Type 1)

Type 1 is graded from 40mm down to dust. The mix of sizes locks together when it is compacted in layers, which makes it the usual choice directly beneath driveways, patios, paths and hardstanding.

  • Type 1 Limestone: crushed quarried limestone and a dependable all-round sub-base.
  • Type 1 Recycled: does the same job, usually at a lower cost and with less environmental impact. Check that your specification allows recycled sub-base.
  • Type 1 Steel Slag: dense and hard-wearing, suited to haul roads, yards and farm tracks carrying heavy vehicles. Tell us where it will be laid, especially near structures.
  • Type 1 IBAA: a recycled sub-base made from incinerator bottom ash. It must be covered by asphalt, concrete or another low-permeability surface, and in England its use without a permit depends on the Environment Agency’s RPS 325 conditions.

Capping and fill: 6F2 and 6F5

6F2 Recycled and 6F5 Limestone are coarser, well-graded materials used as capping and bulk fill. They strengthen weak ground beneath roads and slabs, build up levels, and make firm site access roads, farm tracks and working platforms. They are normally supplied in loose bulk loads for larger jobs.

Where paving or a finished surface is laid on top, Type 1 is usually the layer directly beneath it, with capping below where the design calls for it.

When to use something else

  • Clean stone (10mm, 20mm or 40mm) has the fines removed so water drains through it. Use it for soakaways, French drains and pipe bedding rather than as a compacted sub-base.
  • 20/40mm Crush is an angular hardcore for filling soft spots, making up levels and general groundwork.

Quick comparison

MaterialTypical useCheck before ordering
Type 1 LimestoneDriveway, patio and path sub-baseCompacted depth
Type 1 RecycledDriveways, yards, site roadsSpecification allows recycled
Type 1 Steel SlagHeavy-duty yards and haul roadsLocation, especially near structures
Type 1 IBAASub-base under asphalt or concreteSealed surface and RPS 325 conditions
6F2 / 6F5Capping, bulk fill, working platformsDesign or engineer’s requirements
Clean stoneDrainage, soakaways, pipe beddingSize: 10mm, 20mm or 40mm

Frequently asked questions

Is recycled Type 1 as good as limestone Type 1?

Recycled Type 1 does the same job as quarried Type 1, forming a firm, compactable foundation, and is widely used for driveways, yards and paths. Some specifications require a particular material, so check yours before ordering.

What is the difference between Type 1 and 6F2?

Type 1 is graded from 40mm down to dust and compacts into a tight sub-base for surfaces. 6F2 is coarser and is used as capping and bulk fill to strengthen ground, build up levels and form site roads.

Can I use clean stone as a sub-base?

Clean stone has the fines removed so it drains freely, but that also means it does not lock together like a graded Type 1. It is better suited to drainage, soakaways and pipe bedding.

Need a quote?

Tell us the material, quantity and delivery postcode, or call 07450 701529, Monday–Friday 08:00–17:00.

Our Accreditation

FORS Bronze — Fleet Operator Recognition Scheme